Service Tool Version 3400 Engine
To replace the Routing Engine:. Place an electrostatic bag or antistatic mat on a flat, stable surface. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. For more information about ESD, see.
Manufacturer of Heavy Duty Diesel Engine Tools. Made in the USA. Satisfaction guaranteed since 1986. Toggle navigation. CAT 3400 (15) CAT 3406 (12) CAT 3408 (3) CAT C7 (3) CAT C9 (1) CAT C10 (5) CAT C12 (8) CAT C13 (2). Cam Bearing Service Set - CAT 3406 Engine #20067. $776.14 Carbon Seal Installer - CAT 3406 A.
If you have not already done so, power off the services gateway by pressing the Power button on the front panel of the SFB for three to five seconds. The PWR LED blinks to show you that the services gateway is shutting down. Wait for the services gateway to shut down before you proceed to the next step. Disconnect any cables connected to the AUX or USB ports. Loosen the captive screws at each end of the Routing Engine faceplate. Pull open the ejector handles to unseat the Routing Engine.
Grasp the Routing Engine by the ejector handles and slide it halfway out of the chassis. Place one hand underneath the Routing Engine to support it and slide it completely out of the chassis. Place the Routing Engine on the antistatic mat. Carefully align the sides of the replacement Routing Engine with the guides inside the chassis. Slide the Routing Engine into the slot until you feel resistance, and then press the Routing Engine's faceplate until it engages the connectors.
Press both of the ejector handles inward to seat the Routing Engine. Tighten the captive screws on the left and right of the Routing Engine. Routing Engine status: Slot 0: Current state Master Election priority Master (default) DRAM 1016 MB Memory utilization 39 percent CPU utilization: User 0 percent Background 0 percent Kernel 3 percent Interrupt 0 percent Idle 97 percent Model RE-SRX3400 Start time 2008-11-03 10:25:37 PST Uptime 1 day, 2 hours, 33 minutes, 6 seconds Last reboot reason 0x1:power cycle/failure Load averages: 1 minute 5 minute 15 minute 0.02 0.04 0.00 For more information about using the CLI, see the. If the Routing Engine was replaced on one of the nodes in a chassis cluster, then you need to copy certificates and key pairs from the other node in the cluster:. Start the shell interface as a root user on both nodes of the cluster. Verify files in the /var/db/certs/common/key-pair folder of the source node (other node in the cluster) and destination node (node on which the Routing Engine was replaced) by using the following command: ls -la /var/db/certs/common/key-pair/. If the same files exist on both nodes, back up the files on the destination node to a different location.
Service Tool Version 3400 Engine Problems
For example: root@SRX-B% pwd /var/db/certs/common/key-pair root@SRX-B% ls -la total 8 drwx- 2 root wheel 512 Jan 22 15:09 drwx- 7 root wheel 512 Mar 26 2009 -rw-r-r- 1 root wheel 0 Jan 22 15:09 test root@SRX-B% mv test test.old root@SRX-B% ls -la total 8 drwx- 2 root wheel 512 Jan 22 15:10 drwx- 7 root wheel 512 Mar 26 2009 -rw-r-r- 1 root wheel 0 Jan 22 15:09 test.old root@SRX-B%. Copy the files from the /var/db/certs/common/key-pair folder of the source node to the same folder on the destination node.